![sonance patio series 4.1 outdoor audio system 93429 sonance patio series 4.1 outdoor audio system 93429](https://assetcloud01.roccommerce.net/w458-h458-cpad/_reinders/2/2/2/93429-a.jpg)
Sonance Patio Series 4.1 Speaker System includes 4 satellite speakers and one in-ground subwoofer all powered from a single Sonance DSP amplifier. Continue the above steps for the remaining 2 speakers in the daisy-chain.8-Inch dual voice coil, polypropylene cone subwoofer.Ĥx 3.5-Inch anodized aluminum cone satellite speakers.At the next speaker, repeat steps 2 – 7 for the left channel using the white (+) and green (-) leaving the red (+) and black (-) wires intact.Secure these three wires using the provided silicone filled wire nuts, ensuring that NO COPPER is exposed.Episode Commercial Surface Mount All Weather 70V Series 4 IN. Combine and twist the red wires from the amplifier, the first satellite and the wire running to the next speaker in a clock-wise motion. Performance Outdoor Speaker Systems (15). Strip off 3/4 inch of insulation on the red and black wires to expose the copper conductor.In this example, we want the first speaker to be connected to the right channel so we cut the red (+) and black (-) wires only. Use a wire tie to keep the wire loop intact and act as a strain relief.Or visit the specific brand of cable stripper’s company website for detailed instructions. Why not take the great sound you love inside, outside Our landscape speaker collection offers every possible way to do it.
![sonance patio series 4.1 outdoor audio system 93429 sonance patio series 4.1 outdoor audio system 93429](https://www.sonance.com/assets/media/images/content/Screen_Shot_2019-12-30_at_11_52_53_AM_071204.png)
If you are unfamiliar with using a round cable stripper, please go to YouTube and search for videos on ‘Using a Round Cable Stripper’.
![sonance patio series 4.1 outdoor audio system 93429 sonance patio series 4.1 outdoor audio system 93429](https://assetcloud01.roccommerce.net/w458-h458-cpad/_reinders/4/6/8/93429-e.jpg)
Starting at the first speaker and every speaker that follows, create a loop of wire approximately 6” in length.Leave the wire attached to the spool until the last speaker has been connected. Pull the 14/4 wire on the spool to the furthest speaker location.When subwoofer is in the ground, ensure that there is roughly 5” of exposed subwoofer enclosure from the surface of the ground to the bottom edge of the canopyĬonnecting the speakers using 14/4 direct burial speaker wire. NOTE: The subwoofer requires a burial space that is about 12” diameter and 11” deep. Once the speakers and subwoofer are laid out in their locations and the wiring is completed per this installation guide, stake or mount the speakers into their final locations and bury the subwoofer in its final location. Patio Series 4.1 System w/ Amplifier SKU 93430 Patio Series 4.1 System (no amp) SKU 93429 INSTALLATION Compatible with Sonance 19 ground stakes Complete 4.1 System configuration on a single two-channel amplifier Expandable for up to 8.Run your speaker wire through the trench from the amp to the first speaker location.Be sure to check local codes for trenching limitations. Dig a 4” to 5” trench to run the speaker wires in.Place the 4 satellites and 1 subwoofer in their approximate final locations.Connecting the Speaker Using a 2-Conductor Wire or Low Voltage LIghting Wire.Owner’s Manual OUTDOOR AUDIO SYSTEM Sonance 93429
#SONANCE PATIO SERIES 4.1 OUTDOOR AUDIO SYSTEM 93429 MANUAL#
Sonance 93429 Patio Series 4.1 Outdoor Audio System - Use Manual - Use Guide PDF.